Increase Celluar Reception 3G 2100MHz Cell Phone Signal Boosters for Houses
Model. GW-17W-V
What is a Consumer Signal Booster ?
Consumer Signal Boosters are boosters that can be used in limited areas such as homes, cars and other mobile vehicles and are quite simple to install by following clear step by step instructions. Such devices are delivered usually in plug-and-play format. The user does not require any particular technical expertise to install and use them.
Signal Booster Introduction:
Signal Booster GW-17W-V is designed to enhance and improve the quality of mobile 3G 2100 connection. There’re black and white colors for options. The Led Indicator will show the current level of the input signal, which simplifies the installation of the external antenna. High quality aluminum shell provides an optimal cooling. This model, as simple in connection, installation and configuration, does not require special skills.
Signal Booster Specification:
| Frequency Range | Uplink | Downlink |
| WCDMA 00MHz | 1920 - 1980MHz | 2110 - 2170MHz |
| Max. Gain | 60dB | 65dB |
| Max. Output Power | 15dBm | 17dBm |
| Band width | Wide Band |
| Manual Gain Control | 12dB / 1dB Step |
| Automatic Gain Control | >31dB |
| Ripple in Band | 6dB; |
| Noise Figure | ≤ 6dB |
| VSWR | ≤ 2.0 |
| Intermodulation Products | 9KHz~1GHz | ≤ -36dBm |
| 1~12.75GHz | ≤ -30dBm |
| Spurious Emission | 9KHz~1GHz | ≤ -36dBm |
| 1~12.75GHz | ≤ -30dBm |
| Time Delay | ≤ 1.5 μs |
| Frequency stability | ≤ 0.01ppm |
| MTBF | > 50000 hours |
| Impedance | 50 ohm |
| Power Supply | AC 90-264V,DC 6V/3A |
| Power LED | Power indicator |
| ISO(Alarm LED) | Red | Self oscillation or Strong input signal, ALC>25dB, auto shut down. |
| Green | Normal |
| Mechanical Specification |
| RF Connector | N-Female |
| Switch | Power Switch |
| Cooling | Heatsink Convection cooling |
| Humidity | < 90% |
| Operating Temperature | -20°C ~ +55°C |
| Environment Conditions | IP40 |
| Installation Type | Wall Installation |
| Size | 118mm×90mm×18mm |
| Weight | < 0.8Kg |
Other Frequencies for options:
| Frequency Range | Uplink | Downlink |
| GSM900MHz | 890 - 915MHz | 935 - 960MHz |
| EGSM900MHz | 880 - 915MHz | 925 - 960MHz |
| CDMA800/GSM850 | 824 - 849MHz | 869 - 894MHz |
| AWS1700 | 1710 - 1755MHz | 2110 - 2155MHz |
| DCS1800 | 1710 - 1785MHz | 1805 - 1880MHz |
| PCS1900 | 1850 - 1910MHz | 1930 - 1990MHz |
| LTE2600 | 2500 - 2570MHz | 2620 - 2690MHz |
Signal Booster Features:
1. Coverage up to 500 m²
2. ALC & MGC Function
3. Simple in connection and installation
4. An optimal cooling with aluminum shell
5. Led indicators show working status and ISO alarm.
Support any cellular devices (voice & data & video)
FAQ:
1. After installing booster signal not be very good, indoor signal coverage very small ?
> Adjust outdoor antenna's location and direction
> Change another high gain outdoor antenna
> Check whether cables are connected well
> Change more powerful repeater
2. Cell phone signal full bar, but communication quality bad ?
> Much closer distance between indoor and outdoor antenna, separate them with a longer distance.
3. After installing booster not only signal be good, but also more bad ?
> Much closer distance between indoor and outdoor antenna, separate them with a longer distance.
4. Working good for long time, suddenly signal bad ?
> Check whether outdoor cable connectors are flooded
> Check whether power light is working normally
> If cables are not flooded and power light is working normally, the booster should has problems and need to be sent back to factory for repair.
Signal Booster Application:
Signal Booster Installation:
The booster is fixed onto the wall through expansion bolts.
A. Drill holes on the targeted place and install expansion bolts.
B. Align the holes with the expansion bolts, place flat washers, spring washers, and nuts in turn, and tighten the nuts to fasten the installing support.
C. Place the booster on and fasten it.
D. Connect cables and power cables to the booster respectively.
E. After installing the booster as described above, power on the booster to check the operation status.
Connection:
A. BTS Port: donor antenna cable is connected with Outdoor Port;
B. MS Port: service whip antenna is connected with Indoor Port;
C. DC IN: connected with Power adaptor.
Our Signal Booster Workshop:
Our Company:
Greetwin Tech is a strong and reliable factory, focusing on the R&D and Manufacturing of Digital ICS Repeater, RF Repeater, Indoor Signal Distribution System, Trunk Amplifier, Band Selective Repeater for more than 10 years.
Product Tags:
|
|
Increase Celluar Reception Cell Phone Signal Boosters 3G 2100MHz For Houses Images
|
